Electric Fence Accessories

No more opening and closing gates. Holds cattle, hogs, sheep and horses like an electric fence. Flexible fiberglass polyethylene arms support electrical streamers (30" in length and 6" apart) and bend in any direction. Metal never touches the tractor or vehicle, as it is covered by the fiberglass/polyethylene. Gate swings closed automatically. Easy to install. Energized with any electric fencer.

Protect your valuable horses and livestock from serious injury and unsightly scrapes. Safe-T post caps are designed to conform to a wide range of steel post sizes and stay on tight, eliminating the hazards of sharp, jagged post tops.

Fits the 13-19’ and 18-24’ gate.

Dual function tool used to check electic fence voltages and locate fence line faults. Hand-held unit allows you to quickly move down your fence line, comparing voltage and current readings as you go, to locate short circuits and faults on your fence. A significant change in current ampere readings between one point and the next indicates the presence of a fault between these two points. Unit can be used with or without sound setting, which rises in pitch with the magnitude of the current pulse. Does not require an earth leader. 1-year warranty.

Vinyl sleeves slip over T-posts for safety and appearance. Complete with cap.

These bright white 3" x 5" plastic markers give you a safer, more visible fence, even at night. The stainless steel K-Clips instantly attaches to existing wire fences for geater visibility. Comes packed 12 flags and 12 K-Clips per bag.

Vinyl sleeve fits 4" x 4" x 5' posts including gates and corners. Complete with caps.

Starts working when your fence stops. Provides an instant warning of low or intermittent voltages to detect fencing problems during hours of darkness. Attach to fences near roadways, driveways, buildings, etc., anywhere fence is passed or seen during hours of darkness. When voltage drops, fence alert flashes to notify you of problems. 1-year warranty.

New improved design has numerous adjustments to keep Hi-Tensile wire coil under control. Has adjustable drag to prevent free wheeling of coil. One-inch shaft turns on greased bushing for smooth operation and long life.

Complete ground rod kit to get the most from your electric fence system. contains 3 six foot galvanized rods, 3 heavy duty clamps, 48' connection wire and complete instructions.

Stainless steel clips for use with 3/8" or 1/2" fiberglass posts. Pig tail clips may be used instead of insulators.

Wind up or pay out your electric fence in minutes. Has a crank handle that operates like a ratchet for fence tension; will handle up to 1/2 mile of Bayguard. Heavy duty plastic. Designed so it can be hung from a permanent fence wire or bolted to a post.

Fits the 13-19’ and 18-24’ gate.

Connects to an end tensioner to open gate.

Electri-Gate is a high conductive stretchable cord with a high impact plastic handle. Has an in-line length adjustor for gates from 8 ft. to 20 ft. Comes complete with two 2-way gate anchors.

Fence compression spring is used to determine wire tension on your fence line. One inch of compression equals 150 lbs of tension. Helps absorb expansion and contraction of the fence wire. Made from 1/4” spring steel. Spring is 1 1/2” diameter, expands from 9” to 18”.

Highly conductive 12-gauge aluminum wire insulated with heavy polyethylene coating for up to 20,000 volts. Ideal for all underground applications. One 49' roll is adequate for connection of two standard gates.

Install at convenient locations like fence corners and gates to switch off a section of fence for maintenance and routine checks. Stainless steel contacts. Hardware not included.

Replacement spool for winding and unwinding portable fencing.

In-Line strainer constructed with a galvanized steel frame and aluminum alloy spool and features a spring loaded clip to keep from unwinding. Recommended for high tensile wire use (usually 12.5 gauge wire).

Helps protect your 110-volt plug in energizer from power surges caused by lightning strikes. Plugs into any 110 volt outlet, limits high voltage spikes to 350 volts. Absorbs up to 34 watts of transient power.

Securely splices polywire to ensure that electrical current flows properly. Galvanized to prevent rust.

Ideal when using your fence charger for the first time each season. Recharges your battery overnight, rather than waiting several days for solar energy to charge the battery completely.

Ideal when using your fence charger for the first time each season. Recharges your battery overnight, rather than waiting several days for solar energy to charge the battery completely.

3/4" stainless steel screws for Safe-Fence R-16 Insulators.

Used with Hot Rope or polywire to turn corners or as an end insulator. White only. Bolt measures 6” (measured from the 90 degree angle to the point of bolt.)

Spring loaded PVC gate handle.

A quick, convenient way to splice Hot Rope for a better, stronger splice. Appropriate for use with 1/8" and 1/4" electric rope.

Complete with gate handle, 2 tensioners and 20' tape.

A multi-purpose, high conductive connector that can be used with lead wire to provide a connection from the fencer to your fence or for connecting multiple strand fences together; also a great way to splice ½” poly tape.

Aluminum connector with wire to connect polytape or polywire to your electric fence charger.

High strength plastic ratchet tensioners for use on polywire and polytape up to 1" wide. No need to cut material to tension it, just slide it in and turn for tension.

Quick and convenient way to make a good electrical connection to your polytape or polywire. Complete with two connectors and wire to connect two strands of polytape or polywire.

Suitable for use with any model or brand of low impedance fence charger that has 1 joule or greater output. Provides necessary protection for your charger against the increased voltage surge to your fence created by lightning strikes within several miles. When a Storm Guard Module is in use, it can absorb this surge and fail, instead of causing failure to your fence charger.

Enables you to test the "control factor" of your system and assist you in fault finding, at a very reasonable price. Test voltage under "load" on your fence. Reads from 1,000-10,000 volts; lights glow in sequence to indicate approximate voltage. For use with all fence energizers.

Used for adjusting wire tension with the wire strainers.

For use with ground rods for proper electric fence grounding.