Accessories

No more opening and closing gates. Holds cattle, hogs, sheep and horses like an electric fence. Flexible fiberglass polyethylene arms support electrical streamers (30" in length and 6" apart) and bend in any direction. Metal never touches the tractor or vehicle, as it is covered by the fiberglass/polyethylene. Gate swings closed automatically. Easy to install. Energized with any electric fencer.

Protect your valuable horses and livestock from serious injury and unsightly scrapes. Safe-T post caps are designed to conform to a wide range of steel post sizes and stay on tight, eliminating the hazards of sharp, jagged post tops.

Dual function tool used to check electic fence voltages and locate fence line faults. Hand-held unit allows you to quickly move down your fence line, comparing voltage and current readings as you go, to locate short circuits and faults on your fence. A significant change in current ampere readings between one point and the next indicates the presence of a fault between these two points. Unit can be used with or without sound setting, which rises in pitch with the magnitude of the current pulse. Does not require an earth leader. 1-year warranty.

Fits the 13-19’ and 18-24’ gate.

Vinyl sleeve fits 4" x 4" x 5' posts including gates and corners. Complete with caps.

The Gallagher Fault Finder is a top-of-the-line current meter and digital volt meter built to help you identify and locate faults in your electric fence line. Gallagher’s Fault Finder allows you to check voltage, current, and shorts in one quick step, saving you hours of time!

These bright white 3" x 5" plastic markers give you a safer, more visible fence, even at night. The stainless steel K-Clips instantly attaches to existing wire fences for geater visibility. Comes packed 12 flags and 12 K-Clips per bag.

Vinyl sleeves slip over T-posts for safety and appearance. Complete with cap.

No wire tying, fast and simple. Includes all three end strain elements - insulator, strainer, and steel cable. For corner or end posts. Simply slide over the post and you’re done. Strong, stainless steel cable for long life. Fits up to 8" post. 10-year warranty.

High-visibility LED flashes to indicate fence is working effectively. Clips onto wire or tape. No battery required, powered by the fence. Water and UV-resistant.

Starts working when your fence stops. Provides an instant warning of low or intermittent voltages to detect fencing problems during hours of darkness. Attach to fences near roadways, driveways, buildings, etc., anywhere fence is passed or seen during hours of darkness. When voltage drops, fence alert flashes to notify you of problems. 1-year warranty.

New improved design has numerous adjustments to keep Hi-Tensile wire coil under control. Has adjustable drag to prevent free wheeling of coil. One-inch shaft turns on greased bushing for smooth operation and long life.

Easy-to-read digital design, reads up to 19.9 kilovolts. Matches the performance meter on Parmak fence chargers but will also read all fence chargers accurately. For use with low impedance fence chargers.

The Electric Fence Light is designed to let you know that your electric fence is working properly without any worries. It flashes on and off with every pulse of the fencer with very little draw down of the voltage. Due to the line current, this light is ideal for fencers under 3 joules. The Electric Fence Lights only draw current from your fence until the moment something touches the fence. If something touches the fence, the light will not flash and the full charge will go to whatever is touching your fence. So don’t worry if your tester is showing a draw down on your fence while the light is flashing. Note: Adjust the Knocker spark gap as wide as you can with it still being able to spark. This sensitizes the spark gap with your entire fence, and if something touches the fence, the Knocker spark gap will disengage and the full shock of the charger will go to whatever is touching your fence.

Wind up or pay out your electric fence in minutes. Has a crank handle that operates like a ratchet for fence tension; will handle up to 1/2 mile of Bayguard. Heavy duty plastic. Designed so it can be hung from a permanent fence wire or bolted to a post.

In-Line strainer constructed with a galvanized steel frame and aluminum alloy spool and features a spring loaded clip to keep from unwinding. Recommended for high tensile wire use (usually 12.5 gauge wire).

Fence compression spring is used to determine wire tension on your fence line. One inch of compression equals 150 lbs of tension. Helps absorb expansion and contraction of the fence wire. Made from 1/4” spring steel. Spring is 1 1/2” diameter, expands from 9” to 18”.

Fits the 13-19’ and 18-24’ gate.

24’ spring gate is excellent for electrically bridging wide gate openings. Contracts to 32” when open and includes the unique Safe-Fence tensioners with special gate hood plates to attach the spring and handle to any type of electric fence system.

The Insulated End Strainer is a heavy duty, all-in-one, corrosion-resistant assembly to insulate, and tighten up to 4 mm/15 gauge fence wire. 12-tooth spool for fine adjustment, robust, high-quality, spring-loaded locking clip. Integrated joint clamp allows direct attachment of wires for paralleling and power connection. 10-year warranty.

Complete ground rod kit to get the most from your electric fence system. contains 3 six foot galvanized rods, 3 heavy duty clamps, 48' connection wire and complete instructions.

Electri-Gate is a high conductive stretchable cord with a high impact plastic handle. Has an in-line length adjustor for gates from 8 ft. to 20 ft. Comes complete with two 2-way gate anchors.

Replacement spool for winding and unwinding portable fencing.

Long-life Super Strain Insulator with pre-attached stainless steel cable. No wire tying or special tools required. Fits up to 8" post. 10-year warranty.

Stainless steel clips for use with 3/8" or 1/2" fiberglass posts. Pig tail clips may be used instead of insulators.

Connects to an end tensioner to open gate.

Premium gate handle with comfortable rubber grip and unique internal overstretch protection. The half spring, springload internal mechanism will not allow you to over stretch.

Close your barbed wire gates with an easy crank handle. Easily used by anyone, simply turn the crank to desired tension. A lock can be added to keep out unwanted guests. Mounts with 2 large screws. All steel handle with heavy galvanized steel cable. Comes with 2 large screws and spring pin.

Ideal for use in temporary electric fencing with round posts from 1/4" to 5/8" diameter. Convenient to use when more than one wire is required to hold stock.

Made with heavy-duty alligator clamps and double-shielded, high-voltage wire for leak-proof transfer of power from the energizer to the fence and ground rods. Cords are 46" long and clamps are 3".

Heavy-duty steel construction. Has a tough insulating grip and strong spring. Rated for high-tensile wire.

Premium gate handle with comfortable rubber grip and unique internal overstretch protection. The half spring, springload internal mechanism will not allow you to over stretch.

Highly conductive 12-gauge aluminum wire insulated with heavy polyethylene coating for up to 20,000 volts. Ideal for all underground applications. One 49' roll is adequate for connection of two standard gates.

Helps protect your 110-volt plug in energizer from power surges caused by lightning strikes. Plugs into any 110 volt outlet, limits high voltage spikes to 350 volts. Absorbs up to 34 watts of transient power.

For smooth wire or polywire use only. Clamp around your standard t-post and tighten. Ready for use.

Install at convenient locations like fence corners and gates to switch off a section of fence for maintenance and routine checks. Stainless steel contacts. Hardware not included.

Monitors fence voltage and helps trace shorts in the fence line. Displays fence voltage in 100V increments under 10kV and shows fence voltage from 10kV to 12kV in 1,000 volt increments. Auto ON/OFF function. * Reads the voltage for battery energizers even when the energizers are in Battery Save Mode * Ground rod for ease of ground connection * Fence stud - for quick, no-fuss contact with fence * Powered by one 9V battery * Display to show low battery condition * Improved temperature stability * Water resistant

Spring loaded PVC gate handle.

2 alligator clamps joined by 32” of shielded wire. Connects and transfers power from 1 strand to another. Acceptable for all types of electric fence material.

Securely splices polywire to ensure that electrical current flows properly. Galvanized to prevent rust.

Complete with gate handle, 2 tensioners and 20' tape.

Easily secure your fencing unit to a t-post with the help of this mounting bracket. To be used with fencing model numbers DF-SP-LI (27127) and MAG12SP (27128).

Nylon snap-on clip insulators for use with the Insulated Line Post.

A quick, convenient way to splice Hot Rope for a better, stronger splice. Appropriate for use with 1/8" and 1/4" electric rope.

Suitable for use with any model or brand of low impedance fence charger that has 1 joule or greater output. Provides necessary protection for your charger against the increased voltage surge to your fence created by lightning strikes within several miles. When a Storm Guard Module is in use, it can absorb this surge and fail, instead of causing failure to your fence charger.

Used with Hot Rope or polywire to turn corners or as an end insulator. White only. Bolt measures 6” (measured from the 90 degree angle to the point of bolt.)

Claw style insulator ideal for use in temporary electric fencing with rod posts 3/16" - 3/8" diameter. Fits Ring Top Post (#40990).

Strongest, long-term, end-strain insulation for high tensile permanent electric fencing. 10-year warranty.

Ground rod clamp connects grounding wire to the ground rod.

High visibility black and white expandable electric bungee cord. Expands from 8' to 16'. Includes gate handle and installation hardware.

Aluminum connector with wire to connect polytape or polywire to your electric fence charger.

This tightener is installed without having to disconnect the end of the fence. Can be tightened with a 1/2” drive ratchet. This powder-coated, white, aluminum tightener is best for use with rope or light-gauge wire. Not for use with coated wire.

Quick and convenient way to make a good electrical connection to your polytape or polywire. Complete with two connectors and wire to connect two strands of polytape or polywire.

High strength plastic ratchet tensioners for use on polywire and polytape up to 1" wide. No need to cut material to tension it, just slide it in and turn for tension.

A multi-purpose, high conductive connector that can be used with lead wire to provide a connection from the fencer to your fence or for connecting multiple strand fences together; also a great way to splice ½” poly tape.

Connecting gates to a single post.

A simple 8-light power indicator for standard or low impedance fencers. The lights are calibrated to illuminate from 625 to 7000 volts. Convenient extra long 68" ground cord.

Used for adjusting wire tension with the wire strainers.

Enables you to test the "control factor" of your system and assist you in fault finding, at a very reasonable price. Test voltage under "load" on your fence. Reads from 1,000-10,000 volts; lights glow in sequence to indicate approximate voltage. For use with all fence energizers.

Provides flexibility to liven the fence from either the reel or handle end. Ideal to use with the Geared Medium Reel (#42522).

Replacement stainless steel K-clips for the Fence Flag (#24135) operation.

Connect a fence energizer to 1/4” electric rope or braid. Features a double-post rope clamp connected to a 3/8” terminal with 32” of 12 gauge, shielded wire. May also be used to terminate the rope at the end of the strand.

Connect and transfer power from 1 strand of 1/4” electric rope or braid to another. Features 2 double-post rope clamps and joined by 32” of 12 gauge, shielded wire. May be used to terminate the rope at the end of the fence.

For your easy convenience to splice fence.

For use with ground rods for proper electric fence grounding.

Install the S10 or S16 Energizer on a Gallagher Ring Top Post (#40990) using this post mount. Easy to use and portable!

Converts 110-volt AC power to 12-volt DC power for AC/DC and DC convertible energizers.

Connects power from a 12-volt DC battery to 12-volt energizers equipped with input jack.

The only external fuse protection for fence chargers in the world. Lightning blows up the fuse and not your fencer. Just replace your fuse and you’re good to go.

All-in-one multi-strand electrification gate. Quick and easy to install from one wood post to another. Highly flexible gate width, perfect for whatever space you need. Easy to repair. Should a strand break, simply change out the tape.

For use with these energizers: S10, S16, S22, and B700.

1 1/2" Tape Clip, designed specifically for equine electric fence tape to be securely attached to a Gallagher Insulated Line Post. * Positive locking and quick release to enable re-tensioning of tape * Soft rubber pads lock tape in place to prevent tape movement and fraying * Made from UV High Density Polyethylene strength and long life

* 9 mixed-metal strands - 7/64" * Superior heavy duty strength * White/blue